The interior of the wall is made of lime mortar, while the interior of the angle is cement mortar. The thickness is generally 12mm thick to increase the strength of the angle. Even if this is the case, we must be careful when we are drilling our eyes, so as not to hurt the angle of the sun and cause a great disaster. Once again, the wall, the current wall of the building structure is generally a concrete structure or a frame-type building structure, are using a lot of steel, then when drilling is likely to encounter steel. Let's talk about how a person can complete the installation of a set of glass corners.
Glass corner installation process:
First: Preparation.
1. Glass corners: Matching a group of selected, wipe clean.
2. Hammer: Check whether it is working properly and whether the bit size is suitable. It is recommended to use 8mm drill bit.
3. Cables: Use when the hammer power cord is not enough.
4. Mirror nails: It is best to prepare a few more, so as to avoid defective products, or customers have other needs, can be used as gifts.
5. Cork or bulge: It is recommended to use cork, so you can give yourself more space to install and adjust.
6. Screwdriver: A word or cross, depending on the screw of the mirror nail.
7. Utility Knife: The size and length of the wood plug to be cut.
8. Hammer: Used to pick up a wooden stopper.
9. Pencil: The location used to trace the hole, preferably a thin, pointed, long pencil.
10. Gloves: Be sure to be clean, preferably white, dark and difficult to find dirt.
11. Wooden board: 10cm*40cm or 10cm*50cm, depending on the height of the ground at the time of installation
12. Glass glue: Key moments can be used.
13. Pliers: Ibid.
Second: start the installation.
1. The glass corner must be placed in a safe, flat, soft place, preferably on a wooden board or paper sheet, with the front facing up.
2. All tools are placed in a toolbox, where people take them wherever they go.
3. Determine the height to be installed and place a suitable board under the corner of the wall.
4. Select one of the glass corners. Take the AB combination as an example to determine whether it is A or B.
5. Use your feet to stand on the wood and place a suitable piece of glass horn on the board. At this time, pay attention to the outer edge of the glass kerf out of the wall 2mm.
6. Use a pencil to draw circles in the upper and lower holes. The bigger the circle, the better. To be precise, do not move the glass corners. Don't draw a dot so that the hammer won't find the center point.
7. After painting, remove the glass corner and put it in place. Start drilling with a hammer. First, lightly to see if the position is correct, pay attention to the hammer should be played vertically, do not shake, do not play oblique, force to be uniform.
8. The depth of the hole depends on the length of the screw. Generally, the length of the screw minus the thickness of the glass can only be shallow and deep.
9. Put a cork or bulge. Use a hammer to pry on the wall. Note that the length of the cork should not be greater than the depth of the hole. The tightness of the bulge is far less than that of a cork, and the point at which the screw is screwed is fixed, while the point of the cork is found within a range of about 8 mm.
10. Put the planks and well-marked glass corners back to their original positions, and use your feet, knees, elbows or hands to hold them in place and tighten the screws up to 80%.
11. In the same way, do not add a piece of glass corner to 80% tight.
12. At this time, align the two glass corners up, down, right, left, right, and then tighten the four screws to cover the mirror caps. This set of glass corners is installed.
Third: The solution to the reinforcement.
1. If you come across something that is harder when you punch it, what if you can't get it? Do not use too much force at this time. Ninety percent of them are steel. If you use too much force, the force will be biased. It is easy to crack the corner. The most important way to do this is to glue the glass.
2. First understand the depth of the current hole, according to the depth to select the appropriate cork, the shallower the hole, the more insecure cork.
3. Use the pliers to cut the screws used for the mirror nails to the appropriate length for use.
4. Put the cork in. If the cork is still loose, use a utility knife to cut some pieces of wood. Make sure that the angle of the glass is better. Use a complete screw to unscrew the hole first, and then remove the glass. Remove the horns, make some glass glue around the holes, and then screw them in with the screws.
5. After completing the subsequent installation work, the thorny problems are solved and the installation quality is also guaranteed.
6. Tell the head of the household not to touch the glass corner with hands or objects within 48 hours. Do not move the glass until it has dried.
Through the above introduction, we have a good understanding of the process of installing the glass horn. Thank you for stopping your precious time to appreciate Xiaobian's article. For more information, please continue to pay attention to Qijia Information.
Glass automatic door living room TV glass background wall glass closet door carved glass glass furniture
Furniture Handle,Exterior Door Handle,Nordic Brushed Gold Handle,Space Aluminum Alloy Handle
Guangzhou Junpai Hardware Co., Ltd , https://www.junpaihardware.com