In the printing process, the phenomenon of dirt on the blank part of the printing plate often occurs, which not only reduces the printing rate of the printing plate, but also affects the printing quality. The reasons for the formation and exclusion methods are analyzed and discussed for reference.
First, the dirt caused by the printing plate.
1, underexposure.
Underexposure can cause the photosensitive layer of the blank portion of the printing plate to be incompletely decomposed after the action of ultraviolet light, and cannot be completely dissolved in the alkaline developer during development, thereby causing scumming. The degree of decomposition of the photosensitive layer is in direct proportion to the intensity of the light and the length of the irradiation time, so the selection of the light source and the exposure time are important factors in determining the exposure. Different original versions and PS versions of different manufacturers have different exposure times. We can determine the exact exposure time using a continuous ash scale or Bruner test strip.
The selected print source should have the following features:
1 The layout illumination should be even, so that the four corners and the central part of the plate can be clearly illustrated and the small dots can be aligned.
2 The light source should have a small heat to protect the photosensitive layer from temperature.
3 light source spectrum in the 350 ~ 460nm region. 4 No environmental pollution, no harmful gas precipitation. 5 Low price, simple operation and long service life. The common printing plate light source includes a xenon lamp, a metal halide lamp, and an efficient and fast printing lamp.
2, underdeveloped.
The causes of underdevelopment are:
1 lack of development time;
2 developer concentration is not enough;
3 developer temperature is low. Different pre-sensitized lithographic plates have different alkali resistance and require different developer concentration. Therefore, they are sometimes prepared in accordance with the concentration specified by the PS plate manufacturer. The temperature of the developer should be controlled between 20 and 25 °C. The development time is determined by a gray scale or a test strip, typically about 1 minute.
3, baking version. Roasting is a process that is used to increase the printing rate of printing plates. However, before baking, it is necessary to completely remove the dirty and apply a protective agent, and bake at a constant temperature of 230 to 250°C for 5 to 8 minutes. Otherwise, the photosensitive layer will be carbonized and dirty.
Second, the dirty machine caused by improper adjustment during printing.
1. The pressure between the printing plate and the blanket is too large, so that the oxide film of the blank part is abraded, the sand becomes lighter, and the adsorption is weakened to produce the upper part. Therefore, under the premise of ensuring that the imprinting is robust without spreading, the even use of the minimum pressure can be adjusted by pressing the fuse. The ideal indentation thickness is generally 0.1 mm.
2. The pressure of the water roller, the ink roller and the printing plate is too high, the friction force is enhanced, the sand spot is subject to wear and chemical damage, so that the hydrophilicity of the blank part is reduced and the dirt is dirty. At this time, the steel blade is used to adjust them. pressure. Taking the J2108 machine as an example: The indentation of the water roller and the printing plate is 4 to 6 mm, and the indentation of the ink roller and the printing plate is 5 to 6 mm.
Third, other.
1. During printing, there are dirty marks on the PS plate, on the film base, and on the glass of the plate, which prevent the light from decomposing and becoming dirty. It can be removed by the “double-exposing method of the scattering filmâ€, but the exposure time should not be too long.
2. The ink layer of the layout is too thick, so that the ink layer spreading causes the blank part of the printing plate to have a lower water-repellency and become dirty. We should make the ink layer thicker when the print area or the structure of the paper is loose and rough, and the higher the dot number, the thinner the ink layer.
There are many reasons for the dirtyness of the blank space on the PS version. It is also very complicated, but as long as we carefully analyze and strictly control, we can prevent it from happening.
Deadbolt Lock,Cylinder Lock,Door Lock Latch,Level Lock
Foshan Nanhai Xin Jianwei Hardware Factory , https://www.aaghardware.com