What you need to do before you use a drive-type scrubber for the first time A drive-type scrubber is a product that helps us to clean the floor. It is convenient, fast, and widely recognized. So, how do we operate it properly after choosing a driving type scrubber? Here, experts from Hefei's driving floor scrubbers provide relevant guidance for us. We must do the following preparations before driving the scrubber:
Driving Scrubber 1. Read the instructions provided by the supplier and select the appropriate power box and power box according to the power and voltage of the driving floor Washer.
Pay attention to the power supply should pay attention to the 380V power supply can not be lack of phase, the lack of phase will drive the power of the washing machine burned out. In addition, the instability of the power supply may cause the operating pressure of the driving floor scrubber to be unstable, and the long-term use may cause the motor to be overloaded and burn the motor.
The driving type scrubber experts remind us that because the cross-sectional area of ​​the power cord is small, this will allow the current that is allowed to pass through to fail to meet the current required by the motor, resulting in unstable operating pressure of the driving floor scrubber. Therefore, choosing an appropriate power cord and power box is an important task before driving the floor washer. Then, depending on the flow rate, the proper inlet pipe is selected. If the inlet pipe is too thin, the flow rate will not be able to keep up. Insufficient water intake will cause pressure to fail to meet the standards set by the driving floor scrubber. Long-term use will result in increased wear of seals. , affect the service life of driving type scrubber. General Industrial Driving Scrubber chooses 6 points of inlet pipe.
2. After connecting the correct power supply and water source, there is still a part of work to be done before actually starting the use.
First of all, the high pressure pipe should not be connected to the outlet of the driving type scrubber. After the water source is turned on, water will flow out of the outlet. If there is no water, the inlet pressure is not enough or the check valve in the crankshaft pump is blocked. However, the new one-way check valves are generally not blocked, so it is necessary to solve the problem of water inlet pressure first.
After completion, start the equipment and let the driving scrubber run for about 1 minute without connecting the high pressure hose. Because at the factory, the factory will test the machine and add antifreeze in the driving scrubber. After a long period of transportation, the water in the pump body will turn black. Therefore, the water in the pump body must be drained first. Then connect the high pressure tube and gun, and turn it on for about 1-2 minutes without connecting the nozzle. At this time, in order to squeeze out the air in the high pressure pipe, in order to avoid the occurrence of severe vibration of the high pressure pipe during use.
After the above two steps are completed, you can safely use a driving scrubber to complete your work. Hefei driving scrubber experts, driving scrubber in the process of using can also connect different accessories to complete some special cleaning work. For example, it can be used to clean the floor after connecting the washing platform, and the container can be cleaned after the tank washing device is connected.
Driving Scrubber 1. Read the instructions provided by the supplier and select the appropriate power box and power box according to the power and voltage of the driving floor Washer.
Pay attention to the power supply should pay attention to the 380V power supply can not be lack of phase, the lack of phase will drive the power of the washing machine burned out. In addition, the instability of the power supply may cause the operating pressure of the driving floor scrubber to be unstable, and the long-term use may cause the motor to be overloaded and burn the motor.
The driving type scrubber experts remind us that because the cross-sectional area of ​​the power cord is small, this will allow the current that is allowed to pass through to fail to meet the current required by the motor, resulting in unstable operating pressure of the driving floor scrubber. Therefore, choosing an appropriate power cord and power box is an important task before driving the floor washer. Then, depending on the flow rate, the proper inlet pipe is selected. If the inlet pipe is too thin, the flow rate will not be able to keep up. Insufficient water intake will cause pressure to fail to meet the standards set by the driving floor scrubber. Long-term use will result in increased wear of seals. , affect the service life of driving type scrubber. General Industrial Driving Scrubber chooses 6 points of inlet pipe.
2. After connecting the correct power supply and water source, there is still a part of work to be done before actually starting the use.
First of all, the high pressure pipe should not be connected to the outlet of the driving type scrubber. After the water source is turned on, water will flow out of the outlet. If there is no water, the inlet pressure is not enough or the check valve in the crankshaft pump is blocked. However, the new one-way check valves are generally not blocked, so it is necessary to solve the problem of water inlet pressure first.
After completion, start the equipment and let the driving scrubber run for about 1 minute without connecting the high pressure hose. Because at the factory, the factory will test the machine and add antifreeze in the driving scrubber. After a long period of transportation, the water in the pump body will turn black. Therefore, the water in the pump body must be drained first. Then connect the high pressure tube and gun, and turn it on for about 1-2 minutes without connecting the nozzle. At this time, in order to squeeze out the air in the high pressure pipe, in order to avoid the occurrence of severe vibration of the high pressure pipe during use.
After the above two steps are completed, you can safely use a driving scrubber to complete your work. Hefei driving scrubber experts, driving scrubber in the process of using can also connect different accessories to complete some special cleaning work. For example, it can be used to clean the floor after connecting the washing platform, and the container can be cleaned after the tank washing device is connected.
Jiangsu Dingtian Stainless Steel Products Co., Ltd. , https://www.dingtiancasting.com